sliding mirror title

How to build a sliding mirror door:

Hello Pretty Handy Readers!  Jaime here from That’s My Letter and today I am sharing a sliding mirror project that is the finishing touch on my newly made over walk-in closet.  I will show you how to build a sliding mirror door using wood, wheels and pipe fittings.

This sliding mirror is my solution to a small walk-in closet with no wall space and no back of the door option for a mirror.  The mirror slides across the room on stationary wheels and a galvanized steel pipe track.

sliding mirror 3

My pipe extends beyond the built-ins (mainly because that’s the pipe I had on hand) but this also allows for full access to the built-in compartments.

sliding mirror 5

In the photo below you can see the pipe extends beyond the built-ins at the ceiling:

sliding mirror hardware installed

Simple finger pull holes allow you to glide the mirror along the pipe.  You could get fancy with hardware here but I took the minimalist approach.

sliding mirror 2

Stationary wheels keep the mirror in place while eliminating the need for any lower track system.

sliding mirror wheel detail

Hello super slim profile!  The whole mirror and wood support is only 1 1/2″ thick so the mirror does not protrude out into the room.

sliding mirror profile

Ready to make this clever sliding mirror? Let’s get to it…

Materials:

  • 4 – 1x6x8 tongue and groove planks
  • 1 – 1x6x6 pine board
  • 1 – 1×2 about 16″ scrap pine board
  • 1 – mirror
  • 1 1/4″ brad nails
  • 1 1/4″ wood screws
  • 2 – screw eyes
  • 2 – 2″ stationary wheels
  • stain
  • foam brush & paper towel
  • liquid nails construction adhesive
  • 2 – floor flange (1/2″ galvanized)
  • 2 – nipple (1/2″ galvanized)
  • 2 – 90 elbow (1/2″ galvanized)
  • 1 – 1/2″ galvanized pipe @ 72″ long
  • mollies & 1 1/2″ screws
  • painter’s tape

Tools:

  • nail gun
  • drill & drill bits
  • wood glue
  • sander & sandpaper
  • saw
  • hammer
  • measuring tape
  • pencil
  • 1 1/4″ spade bit

Below are the plumbing parts used for this installation (buy two of each):

sliding mirror parts

Before building the mirror, measure your floor to ceiling height then subtract the wheel height, the screw eye height and plumbing parts. This will vary for each installation but from there you can determine the length of the boards.

Step 1:

Cut tongue and groove boards to length.  Attach the 1×6 horizontal board across planks at both ends using wood glue and 1 1/4″ brad nails. But, be sure to leave space for the mirror between the 1×6 boards:

sliding mirror step 1

Step 2:

Flip over and add 1 1/4″ countersunk screws into planks and 1×6 for additional support:

sliding mirror step 2

Step 3:

Sand smooth:

sliding mirror step 3

Step 4:

Apply stain with foam brush and wipe excess.  Let dry.  If desired seal with poly.

sliding mirror step 4

Step 5:

Squeeze out a generous amount of liquid nails construction adhesive:

sliding mirror step 5

Step 6:

Press mirror in place and let dry following product guidelines:

sliding mirror step 6

Step 7:

Pre-drill holes and insert screw eyes:

sliding mirror screw eye

Step 8:

Attach a horizontal 1×2 at back using wood glue and countersunk 1 1/4″ screws.  This will give you a place to secure the wheels. Pre-drill and attach wheels to bottom of boards:

sliding mirror wheels

Step 9:

Moving on to the hardware installation.  Determine placement on the ceiling (my hardware is mounted about 6″ out from the built-ins).  Hold flange in place and mark holes with pencil, pre-drill holes for mollies then hammer mollies in place. Then, screw flange in place and attach nipple and elbow:

sliding mirror hardware step 1

Step 10:

Temporarily screw pipe into installed elbow and then add fittings at the other end.  This is only temporary at the moment just to mark the position on the ceiling:

sliding mirror hardware step 4

Step 11:

Mark the flange position on the ceiling and pre-drill for mollies.  Insert mollies with hammer.  Then remove the unattached fittings and unscrew the pipe.

sliding mirror hardware step 2

Step 12:

Slide the pipe through the screw eyes on the door then screw pipe into fittings at far end:

sliding mirror hardware step 3

Step 13:

Attach fittings to open pipe end and screw flange into position in the ceiling.  ** Be certain to check door function before adding all screws. Then, you can adjust the height by screwing or unscrewing the screw eyes if necessary.

sliding mirror hardware step 5

Step 14:

Determine position for finger pull. Wrap side of plank with painters tape to prevent tear out and use a 1 1/4″ spade bit to slowly drill holes then sand smooth:

sliding mirror finger pull

The sliding mirror door is complete.

sliding mirror 4

Conclusion:

Hope you enjoyed this alternative use of plumbing parts combined with a mirror on a closet.  This sliding mirror project could work in a variety of situations, think beyond the standard mirror installation and you might surprise yourself! No you know how to build a sliding mirror door.

Jaime signature

 

Pin for later!

16 replies
  1. Charles
    Charles says:

    How well do the eye bolts work? I’ve tried building something similar but with 3/4″ pipe and 1″ tees, but there is too much lateral movement when the door is moved and the tee catches on the pipe, preventing the door from moving. I think the eye screws might work better as that lateral movement would be significantly less, but I’m also using an actual barn door, not something custom-built, so weight might be an issue, too.

    Thanks for any comments. Great work, BTW!

    Reply
  2. Christy
    Christy says:

    I did NOT expect to actually find what I was looking for when I googled “how to build a mirror barn door.” This is a much simpler and more feasible version of the solution I was trying to come up with for two odd-sized bedroom closets I framed in on either side of a refrigerator nook in the kitchen on the other side of the wall. I’m especially thrilled to find my solution designed by another female renovator. All this just to say: Thank you for existing. Best wishes! Christy

    Reply
  3. Janet A.
    Janet A. says:

    I want to know about the noise… does this make a terrible metal on metal noise or is the trick to have the eyes only looped through the pipe and not actually hanging on it?

    Reply
    • Jaime Costiglio
      Jaime Costiglio says:

      Hi Janet, yes the trick is to have the pipe run precisely down the middle of the eyes which is why it’s important to adjust the eyes (screwing in more or less) before attaching the final flange to the ceiling. My floors are extremely uneven and not level so mine makes noise at the far end but we hardly ever glide it down to that end.

      Reply
  4. Bonnie (BornInaZoo)
    Bonnie (BornInaZoo) says:

    It took me a while and google to figure out WTH are mollies (since there are none in the pictures). Ahhh … screw anchors. Molly seems to be a regional term for those. {Don’t fret … the guys here call structural lag screws “Germans” … because the box they came in was from Germany.}

    Reply
  5. Rosalie
    Rosalie says:

    omg- I just found your page on FB and will be following you. I only saw a few of your posts and I am already excited to see more.

    Thank you!

    Reply

Trackbacks & Pingbacks

  1. […] I’m over at Pretty Handy Girl sharing how to build and install a sliding […]

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.