, , , , , , , , , , , , ,

Vintage Coca-Cola Dog Bowl Crate – Guest Posting by Sew Woodsy

vintage coca-cola crate turned dog bowl

I met Katie & Jon at Haven recently and fell in love with their DIY Tutorial blog, Sew Woodsy, immediately. This fun couple really write great tutorials, like the DIY Corn Hole Game

…and a Sew Your Own Yoga Skirt tutorial.

So give it up for the FAB DIY duo! Sew Woodsy!!!

Thank you Brittany for inviting us to guest post for you today! We are so excited to be here and share a fun DIY project.

Sew Woodsy

For those who don’t know us, we are Katie & Jon, authors of SewWoodsy.com. We are a husband and wife DIY team: we document our journey of homeownership one tutorial at a time. Sew Woodsy is a place where we share our love for renovating and decorating on a budget. Each of our blog post includes detailed tutorials and photographs to help the average person become a DIY expert.

Vintage Coca Cola Crate Turned Dog Bowl Holder

Our neighbor came to us the other week and asked if we could drill holes in an old Coca-Cola crate to make a dog bowl holder for her 5 month old yorkie. She was hoping this would solve the problem of him picking up his bowl and running around the house with it once he was finished! Our neighbor just wanted us to flip the crate over and drill holes. If we did this, the Coca-Cola writing would be upside down, so Jon (aka Mr. Woodsy on the blog) took it to the next level! This vintage Coca-Cola crate turned dog bowl holder was made within 30 minutes. Follow our step-by-step tutorial to make your own.

Supplies:

  • Vintage Coca Cola Wood Crate (eBay is a good source for this)
  • 3/4 inch plywood,
  • Table saw
  • Drill
  • 1/2″ Fostner drill bit
  • Jigsaw
  • Nail gun & compressor (or finish nails and hammer)
  • Tape measure
  • Compass
  • Center punch
  • Hammer
  • Red spray paint
  • Orbital sander with sand paper

vintage coca cola dog bowl

1. Cut the 3/4 inch piece of plywood to the size of the vintage coca cola crate opening. Our crate opening was 14 inches by 10 inches.

Vintage Coca Cola Crate Turned Dog Bowl

*I like to check that my blade is square with my fence on my table saw.

Vintage Coca Cola Crate Turned Dog Bowl

2. After my first cut I check the size of the piece of plywood to make sure it fit in the crate. You will want your piece of wood to fit in the crate snug.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*At this point I’ll trim up the piece of wood to create the snug fit.

Vintage Coca Cola Crate Turned Dog Bowl Holder

3. Measure the diameter of the dog bowl. *For this tutorial to work for you your dog bowl will need to have a slight lip on the edge for it to rest on top of the wood.

vintage coca cola crate turned dog bowl holder

4. Now that I know what the diameter is of the bowl I measure for placement on the plywood. *Because this is for a small dog I didn’t want to center the bowls because I wanted to ensure he would be able to eat from the bowls.

Vintage Coca Cola Crate Turned Dog Bowl Holder

5. Now I divide my diameter of the dog bowl in half to get the radius. In this case my dog bowl was 5 inches across so I’ll have a 2.5 inch radius.

Vintage Coca Cola Crate Turned Dog Bowl Holder

6. Using a tape measure, I set the placement for the two bowls lengthwise so that they are evenly spaced out.

vintage dog bowl crate

7. Using a compass begin drawing the circles for your two dog bowls.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*This is what your piece of plywood should look like after you are done drawing your circles.

Vintage Coca Cola Crate Turned Dog Bowl Holder

8. Next, you’ll want to drill a small hole large enough to fit the blade of a jigsaw in the wood.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*I used a half-inch fostner bit.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*This is what my piece of plywood looked like after I drilled the two holes in the board.

Vintage Coca Cola Crate Turned Dog Bowl Holder

9. Using a jigsaw you’ll want to carefully cut out the first circle.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*Make sure you cut along the inside of your markings so that your dog bowl doesn’t slip through.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*My first hole cut and I double checked to make sure the dog bowl would fit in the hole snug.

Vintage Coca Cola Crate Turned Dog Bowl Holder

10. Using a piece of sandpaper I sanded down the edges and cleaned up the inside of the hole so that the dog bowl fit better!

Vintage Coca Cola Crate Turned Dog Bowl Holder

*Then, I double checked again to make sure that the placement of the hole would be acceptable distance for the dog to reach the food bowl.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*You’ll also want to double check that the dog bowl doesn’t bottom out on the crate.

Vintage Coca Cola Crate Turned Dog Bowl Holder

11. Next up, grab your can of spray paint, and begin lightly spray painting the piece of cut-out plywood.

Vintage Coca Cola Crate Turned Dog Bowl Holder

12. Grab the orbital sander and give it a light sanding to distress it to match the vintage crate as best as possible.

Vintage Coca Cola Crate Turned Dog Bowl Holder

Your vintage Coca Cola crate turned dog bowl holder is almost complete!

Vintage Coca Cola Crate Turned Dog Bowl Holder

Vintage Coca Cola Crate Turned Dog Bowl Holder

13. Using a pneumatic nail gun (and air compressor) shoot a few nails along the sides of the crate to hold the plywood in place.

Vintage Coca Cola Crate Turned Dog Bowl Holder

*If you don’t have a nail gun you can use finish nails and a hammer to secure the top piece of plywood. As pictured above, use a center punch so that you don’t destroy your crate when hammering the nails in.

Now let your pup test it out!

Vintage Coca Cola Crate Turned Dog Bowl Holder

I think he likes it!

Vintage Coca Cola Crate Turned Dog Bowl Holder

And he has discovered multiple ways to eat dinner!

We hope you enjoyed our tutorial. If you decide to make one we would love to feature it on Sew Woodsy! Don’t forget you can always follow us on Facebook, Twitter, and Pinterest!

Thanks again Brittany for having us over!

Thank you so much to Katie & Jon for that great tutorial. That doggy dining station is adorable! I might be making one of those soon for Pretty Handy Dog.

Head over and start following Sew Woodsy if you want to receive more DIY goodness. Tell ’em I sent ya’ and they’ll give you a big fat discount on their posts! 😉 Kidding, it’s all free of course.

 

6 replies
  1. gail
    gail says:

    LOVE Katie and Jon! It was such fun getting to meet them in Atlanta!
    Fabulous job Jon! the crate is adorable, so happy you left it upright. I’m a coke girl…so of course I would love this.
    brady is so darn cute!

    gail

    Reply
  2. Edie
    Edie says:

    I am Mr. and Mrs. Woodsy’s lucky neighbor. The doggie dish is wonderful! Brady is one happy puppy thanks to their fantastic woodworking skills. It is so cool to see it on your blog. 🙂
    Edie

    Reply

Trackbacks & Pingbacks

  1. […] and Jon of Sew Woodsy shared at Pretty Handy Girl how they turned an old soda crate into a very cool dog bowl holder. Apparently, their neighbor’s […]

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.