Circle Diamond Pattern Light Fixture – Updating a Brass Light Fixture

circle_diamond_pattern_light_fixture_pin

I have been dying to share this tutorial with you! This project was inexpensive and it made such a big impact in our mudroom. It started with a few Habitat ReStore light fixtures and some NEW! Martha Stewart glass paint and ended up adding some major “WOW Factor” to our entry.

[Read more...]

Installing an Anti-Tip Bracket for Your Oven

I hate to break up the holiday glamour-fest, but it is time to put on my tool belt and share with you an important safety device. As some of you may remember, we had an oven fire this past September. We ended up replacing our oven and when the new one was delivered it came with an anti-tip device. All new free-standing and slide-in ovens should come with one. Be aware that most stores that deliver your stove WILL NOT install the anti-tip device when they deliver (shame on them!)

Oven.jpg  

If you don’t know what an anti-tip device is, let me show you:

BracketParts.jpg

That’s it! Just a bracket and a few screws. But, that little device can prevent this:

TippingPics.jpg

The whole oven can and will tip very easily with very little weight on the open oven door. Stop reading RIGHT NOW and go open your oven door. Then press down to see if you can tip your oven!

If you can tip it, you can call the manufacturer of your oven and they should send you a device for free or just a shipping charge. HERE is a website with a listing of the phone numbers for most major appliance manufacturers. Or I have one extra anti-tip device from our old GE stove, so let me know if you would like it and I’ll send it to you free of charge.

Installation is super simple. The hardest part is pulling the stove out and cleaning all the goodies that have fallen beneath the stove for years. Apparently our stove doubles as a matchbox car garage!

CarGarage.jpg

Safety Alert: If you notice in the picture above, there is a metal box lying loose on the floor with black and grey wires entering it. This is the junction box where our wiring for the stove is hardwired into the house. The fact that this junction box is lying loose on the floor is dangerous! Should we (or the firemen) had pulled hard enough when removing the stove, the connections could have come loose and there would be 240 volts of live (or should I say life-ending) power exposed! Therefore we hired an electrician to wire an outlet into the wall before we installed our new stove.

One more safety tip, if your oven catches on fire (specifically the heating element is burning) you will need to stop the oven from receiving any power. Be sure to turn off the circuit at your circuit breaker! This probably would have saved me from having to call the fire department, I thought just turning the oven off would stop the element from continuing to ignite and burn, BUT NO IT DID NOT!

Installation:
If your oven is hardwired, before installing the bracket be sure to shut off the power to the appliance. Even if you have an outlet, be extra safe and turn off the power to that outlet.

Once you have removed all foreign objects from under the stove and cleaned the floor. Layout your template lining up the corner of the sheet to the corner of your cabinet and the wall.

LineUpTemplate.jpg

Drill through the crosshairs marking the location of the screws (remember to use a drill bit slightly smaller than your screws.)

DrillHoles.jpg
Remove your template, line up your bracket with the holes and drive the screws through the holes on the base of the bracket and then into the wall at the back of the bracket.
LineUPBracket.jpg
Once your bracket has been installed, grab a helper to help you guide your oven back behind the wall.
InstalledBracket.jpg

If you are having trouble lining up your stove with the bracket, you may need to remove the storage drawer and look underneath your oven. You also might need to adjust the feet on your oven up or down to give enough clearance for the whole foot to slide into the bracket. (You do this by screwing or unscrewing the feet.) Be sure to adjust the foot on the opposite side to level your oven.SlideFootUnder.jpg
And you are done, this installation is relatively easy as long as you don’t encounter things like electrical code violations (aka improperly hard-wired appliances.) Feel free to email me with any questions and I will try to assist you. Again, I have one extra anti-tip device for a GE stove if you would like it.

Now it is time to bake some cookies! YUM!