, , , , , ,

Installing Semi-Rigid Dryer Hose to Prevent Fire Hazard

It’s time to take on a little fix in your laundry room. This single upgrade can prevent your home from a house fire. Let me show you how installing semi-rigid dryer duct can prevent a fire hazard!

Installing Semi-Rigid Dryer Hose to Prevent Fire Hazard

Installing Semi-Rigid Dryer Hose to Prevent Fire Hazard

Last year when I showed you how to clean out your dryer hose to prevent dryer fires, I didn’t realize that I still had a fire hazard living in our laundry room. Since then, I stumbled across a video that scared the bejeezus out of me. Matt from Great Lakes Home Performance created this video showing what happens to foil dryer hoses.

I knew that white plastic dryer hoses were bad and had previously replaced ours with the flexible foil hose. But, I felt duped when Matt showed what happens to those “foil” hoses. First, what I didn’t realize is that those shiny metal hoses aren’t foil! They are made of flammable plastic. Go ahead, run to your dryer right now and see what type of duct work you have — I’ll wait. If it is white or shiny foil, I’ll show you how to replace it with semi-rigid duct to keep you and your home safe from a dryer fire. This is an easy tutorial, you can definitely do this (if your exterior dryer vent is on the 2nd floor, you can keep the same vent and just replace the hose.)

Materials:

(I’ve included affiliate links for your convenience. I earn a small percentage from a purchase using these links. There is no additional cost to you. You can read more about affiliate links here.)

semi rigid dryer hose

 

How to Replace the Dryer Vent Cover:

First, take a look at your dryer vent outside your house. Is it loaded with lint? If so, follow my tutorial for cleaning your own dryer vent.

how to clean your dryer vent outside

 Does the vent stick open or have gaps in it?

lint gap vent

Were you nodding your head, yes? Well, if you like to keep your home rodent and bug-free, I highly recommend replacing the exterior vent at this time.

Detach the dryer duct (hose) from the wall inside your home first. Use the screwdriver to loosen the hose clamp.

detach dryer hose from vent

Or if you have the tension style clamp, pinch the clamp wings together to release the hose.

Installing Semi-Rigid Dryer Hose to Prevent Fire Hazard

Head back outside. Unscrew the mounting screws from around the dryer vent and lift the dryer vent off.

remove exterior vent cover

Slide the new vent into the hole and attach it to the house with the screws provided.

replace dryer vent

For additional draft and bug protection, caulk around the edge of the vent cover where it meets the house.

When the dryer is on and air is forced through the duct, the louvers will open.

dryer vent opens when air blows

When the dryer is off the louvers will close and prevent unwanted house guests (spider, mice, etc.) from taking up residence into your dryer.

Ahhhh, much better, right?!

before after dryer vent

Periodically check the vent to make sure the louvers close and there is no lint build-up.

How to Replace the Dryer Duct Hose:

Pull your dryer out from the wall. Now is a good time to vacuum behind it to clean up any lint that has accumulated back there.

Installing Semi-Rigid Dryer Hose to Prevent Fire Hazard

Hold the adjustable elbow next to the vent duct where it enters your laundry room. If it is too long, trim it with the tin snips to the depth of the elbow.

measure and trim dryer vent

1) Feed the collar over the vent duct to cover the hole in the wall  (and seal out any drafts.) Attach the collar with screws.  2) Feed one hose clamp over the vent duct.

connect elbow to dryer vent

3) Slide one elbow over the vent duct. 4) Tighten the hose clamp with the screwdriver until the elbow is secured to the duct. Tug lightly to make sure it won’t inadvertently slip off.

If you are having trouble slipping the elbow into the duct, you can use pliers to cut the tabs on the crimped end to allow you to collapse the collar a little more.

crimp pipe flutes

Remove the semi-rigid duct from the packaging. Extend the hose only long enough to reach your dryer. If your distance is short (and the duct too long), you might need to trim excess duct with the tin snips.

How to Connect the New Dryer Duct:

1) Slide the hose clamp over the end of the elbow. 2) Slip the semi-rigid duct over the elbow.

attach hose to vent

3) Slide the hose clamp over the semi-rigid duct and elbow. 4) Tighten the hose clamp until the duct is secured to the elbow. Gently tug the semi-rigid duct to make sure your connection is tight.

Shimmy behind your dryer (this reminds me of the time I was pregnant and had hired a handyman to re-route our dryer hose to a closer location. Handsome Guy and the Handyman were both struggling with the short duct and couldn’t attach it. I really wanted to push them both aside and do it myself. Unfortunately, at that point in my pregnancy, my belly’s depth was equal to my width and there was no shimmying behind any dryer for me.)

1.) Slide the hose clamp over the dryer exhaust. 2) Attach the elbow to the dryer.

attach elbow to dryer

 

3) Tighten the hose clamp onto the dryer. 4) You’ve got this right? Tighten the hose clamp onto the semi-rigid duct and elbow.

BAM! You’re done! When you push your dryer back, make sure you aren’t crushing the ductwork. Are you happy you learned how to install a semi-rigid dryer duct to prevent a fire hazard? Don’t forget to clean out your dryer and the ductwork at least twice a year.

connected semi rigid dryer Hose

Take care and stay safe! I care about you all a lot.

dryer vent safety

 

You might also like:

how to clean out your dryer ducts

How to Clean Out Your Dryer Ducts to Prevent Fires

 

keep HE Clothes Washer CLean

Learn how to keep your HE Washer Clean like the day it was delivered!

 

Miracle Stain Remover

DIY Laundry Detergent & Miracle Stain Remover

 

 

61 replies
« Older Comments
  1. Emily Fine
    Emily Fine says:

    Regarding photo #2 where you shimmy the semi-rigid hose over the elbow duct. HOW? They are EXACTLY the same size, and I can’t fit the hose outside or inside the duct. I’m at risk of distorting the metal so much it’ll be useless, and I don’t have a crimper.

    Reply
  2. Judah
    Judah says:

    Brittany- you rock- amazon doesn’t stock that kit anymore- also, how to test if the final ductwork is leaking air ?

    Reply
    • Brittany Bailey
      Brittany Bailey says:

      Thanks for letting me know about the Amazon link. I updated to a similar item. Regarding leaking. You can do one of two things. The first is to wet your hand and slowly run it along the ductwork. You should be able to feel any air on your wet skin. The other option is to hold a fluffy feather and run it along the duct looking for the feather to tremble. (I think you could use a lit match too, but this is a bit more dangerous, especially around a lot of lint build up.

      Reply
  3. Rebecca
    Rebecca says:

    Wow…never knew this! Thanks so much for this important information. I am in the process of buying a house and would never have known this had I not stumbled upon this video!

    Reply
  4. Ken Bell
    Ken Bell says:

    What secures the sleeve through the wall? i see it does not attach to the louvered vent and also with a pipe clamp to the first 90. but prvents the 90 and hose from slipping out?

    Reply
  5. Alex
    Alex says:

    Selling my home and the buyer’s inspector suggested I do this. I thought I already had the fireproof kind, thanks for helping me understand.

    Reply
  6. Deb M
    Deb M says:

    I know you posted this fantastic tutorial several years ago, but I’m hoping you can tell me where you got the white plastic collar that you put over the vent duct to cover the hole in the wall (on the inside wall). I’ve searched online for it with no luck. Thanks!

    Reply
  7. Toni Piel
    Toni Piel says:

    I want a FIREPROOF sleeve that will slide over the 4″ pipe that goes thru the wall. There are several wires in the wall that are above the vent that could catch fire. Do you
    have any recommendations? Thanks.

    Reply
    • Anne
      Anne says:

      I saw a tutorial online where a guy enlarged the hole to 5″ and slid a 5″ aluminum vent pipe into the space (very slightly angled downward so condensation will run outside). He caulked the space between that pipe and the wall. Then he slid a 4″ dryer vent pipe through the 5″ pipe, inserted pieces of flame-retardant foam or insulation between both pipes (to hold the 4″ pipe in the center of the 5″ pipe), and used fire-retardant expanding foam (small expansion so the pipes aren’t bent/distorted) between both pipes.

      Reply
  8. Erin
    Erin says:

    Thanks so much for posting this– I replaced my foil dryer vult vent with a semi-rigid one today. I did have to use Nashua tape to seal the new duct to the elbows, but other than that it worked well.

    Reply
  9. Megan
    Megan says:

    Great post! Please excuse my ignorance, but why are the “elbows” necessary? Is there a reason you can’t connect the semi-rigid hose without the elbows?

    Reply

Trackbacks & Pingbacks

« Older Comments

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.