We had a great turnout at the Habitat ReStore demonstration on Saturday! Thank you to everyone who showed up. It was nice meeting some new friends. There will be another talk at 1 pm on Saturday, December 10th at the Cary, NC Habitat ReStore! I hope you can make it, because I’ll be showing how to turn some common ReStore items into holiday gifts and décor.
And now for the tutorial that you really wanted to see — but couldn’t make it to see — making a shoe storage bench out of an kitchen wall cabinet!
Wall cabinets that fit over your fridge or stove work really well for this shoe storage bench project. Ideally the cabinet will be 18″ in height (standard seat height). If it is shorter, you can build a base for your bench to raise it up a little.
It is more than likely that these cabinets will be coated with about 5 lbs. of grease. But, have not fear, I found THE BEST cleaner for removing grease. Hot water and ammonia! You must work in a well ventilated area when working with ammonia. Sponge on the ammonia and hot water concoction and wait about 10 minutes. Wipe off the cabinet and repeat until clean.
- Ammonia, hot water and a sponge or rag (to clean off grease)
- Nail set
- Miter saw
- Tape measure
- Wood putty
- Construction or thick wood glue
- Paint brush
- 2″ finish nails
- 1 and 1/4″ finish nails
- Quarter round moulding for base of cabinet
- Cove moulding for top of cabinet
- 1″ thick board (cut to fit inside cabinet dimensions)
- 1×4″ pine firring strips
- Plywood or pine board cut to fit 3″ wider and 1.5″ deer than finished dimensions of the cabinet (after moulding is added.)
- Optional: Thin plywood to use as a filler strip
Measure the inside depth of the top of your cabinet.
Cut three 1×4″ boards to sit on top of the cabinet and use for the bench support and to give your nails something to grip when attaching the bench top. (Without these supports it would be very difficult to nail or screw into the particle board cabinet without it flaking and chipping.)
Use thick construction glue to attach the boards. (Glues that have a toothpaste consistency.)
Nail finish nails into the boards at an angle to secure them.
For good measure, nail two more finish nails through the back of the cabinet and into the ends of the support boards.
Measure your cabinet sides and front. Cut quarter round (convex shape) for the base of your cabinet and cove moulding (concave shape) for the top of your cabinet.
Here is a close up of the moulding I used for the base and crown of the cabinet.
If the face frame of your cabinet juts out past the side, you’ll have a gap (see below). No worries, we can fix that!
Rest your moulding on top of the filler strip.
Predrill holes in your trim moulding, then hammer finish nails to secure the trim. If you are using a finish nailer to secure the moulding pieces, you won’t need to pre-drill.
Fill any nail holes or cracks with wood putty.
Fill the seams of the filler strips with wood putty too.
For the top of your bench, cut a piece of wood that is 3″ wider and 1.5″ deeper than the top dimensions of the cabinet (be sure to measure to the edge of the crown moulding.) Sand it smooth. Stain or paint the bench top.
*For demonstration purposes, the video will show how I attached the bench top with glue and finish nails from the top: Add some construction glue to the wood supports. Then, nail the top into the three support boards on top of the cabinet. Fill the holes left by the nails. And touch up the spots with stain or paint. Either way will work, but the screws from below will save you the work of adding wood putty and/or touching up the nail holes.
To install the shelf, level the board you cut to fit inside the cabinet (or shall I call it a bench since we are almost done!)
Use either “L” brackets inside the cabinet to hold the shelf or hammer nails from the side and into the ends of the shelf to secure it. Luckily shoes aren’t super heavy, so you can get away with using finish nails to hold the shelf in place.
Gently sand the cabinet and shelf to scuff up the surface and give it a “tooth” for the primer to adhere to. Prime the cabinet and bench.
Sharing this tutorial with Home Stories A2Z Tutorials and Tips Link Party and The Shabby Creek Cottage’s Transformation Thursday